PENOSIL
SpeedFix Construction 878

VALUES

• Great adhesive properties
• Low curing pressure and post expansion
• Thermal and sound insulation
• Works in all weather conditions
• Strong structure
• Adhering and sealing narrow joints
• For interior and exterior use

USAGE INSTRUCTIONS

Surfaces must be clean from dust, loose particles and oil stains.

Moisten dry surfaces with water mist (only at temperatures above zero) to ensure a faster curing time and better end results.

Application with foam gun:
Shake the can vigorously at least 20 times. Hold the foam can in an upright position with the valve up.
Screw the can onto the gun. Hold the can upside down when extruding the foam. Foam output can be adjusted with a gun trigger and adjustment screw.
Do not aim the gun at people. Avoid screwing the can onto the gun with the valve upside down. Do not screw the gun onto the can. Do not bend or turn the can during screwing.

EasyGun applicator:
Shake the can vigorously at least 20 times. Remove the cap. Hold the foam can in an upright position with the valve up.
Place the applicator onto the valve, press slightly until the applicator is fixed. Hold the can upside down when extruding the foam.
Foam output can be adjusted with the applicator trigger.

Insulation boards and interior design boards:
Apply the foam adhesive to the board surface in a continuous flow, parallel with the sides of the board (3 to 4 cm from the edge) and one strip in the middle, parallel to the longest side (up to 25 cm between adhesive strips).
After applying the foam adhesive onto the board wait 2 to 3 min and then press the board onto the wall.
The board can be adjusted/straightened during the next 5 min. With one foam can 10 m2 of wall surface can be covered with insulation boards.

Windowsills:
Before fixing the windowsill, make sure the base surface is levelled. Spacers must be used to support the windowsill; foam can only be used as an adhesive.
Apply foam adhesive to the base surface 3 to 4 cm from the edge.
Weights must be used to fix the windowsill until the foam adhesive is cured.

Construction blocks:
Foam adhesive can be used for building non-load-bearing interior walls. The first row of blocks must be well levelled using mortar.
Foam adhesive should be applied to both vertical and horizontal surfaces. Wait for a few minutes after applying the foam adhesive and then press the stone surfaces together.
Foam adhesive can only be used in case even distribution of loads from block to block is ensured.
Not suitable for distributing or carrying loads.

TIPS

• Air temperature during use: -5°C to +30°C.
• Always follow building design, building regulations, standards or other relevant guidelines concerning additional mechanical fastening when covering insulation boards with cladding materials.
• Use of insulation support anchors is always recommended.
• Consult with a sales agent, a dealer or an architect regarding compatibility with various stone-based materials and other technical issues.
• Due to the wide variety of construction materials, we recommend a preliminary compatibility test.
• Working at low temperatures, the foam can must be prewarmed to room temperature (around +20°C).
• Use Penosil Foam Cleaner 929 to clean tools and surfaces from uncured foam.
• Use Penosil Multipurpose Wipes 943 to clean hands and clothes from uncured foam.

More expert tips in FAQ

LIMITATIONS

• Does not adhere to polyethylene (PE), PTFE (Teflon®) or silicone surfaces.
• Do not use at temperatures below -5°C.
• Cured foam needs to be covered with a suitable material to protect against UV rays.
• Not recommended for bituminous surfaces.
• Windowsills must have additional constructional support, foam can only be used as an adhesive.

SAFETY INFORMATION (CLP AND REACH)

DANGER

H222 – Extremely flammable aerosol.
H229 – Pressurised container: May burst if heated.
H302+H332 – Harmful if swallowed or if inhaled.
H315 – Causes skin irritation.
H317 – May cause an allergic skin reaction.
H319 – Causes serious eye irritation.
H334 – May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 – May cause respiratory irritation.
H351 – Suspected of causing cancer.
H373 – May cause damage to organs through prolonged or repeated exposure.
P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Do not pierce or burn, even after use.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves/ protective clothing/ respiratory protection/ eye protection/ protective footwear.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C/ 122°F.
P501 Dispose of contents/ container in accordance with local/ regional/ national/ international regulation.
EUH204 Contains isocyanates. May produce an allergic reaction.
Substances that contribute to the classification: 4,4´-methylenediphenyl diisocyanate, isomers and homologues; Reaction products of phosphoryl trichloride and 2-methyloxirane; Glycerol, propoxylated
Persons already sensitised to diisocyanates may develop allergic reactions when using this product.
Persons suffering from asthma, eczema or skin problems should avoid contact, including dermal contact, with this product.
This product should not be used under conditions of poor ventilation unless a protective mask with an appropriate gas filter (i.e. type A1 according to standard EN 14387) is used.
As from 24 August 2023 adequate training is required before industrial or professional use.